ARTTEC I CUTTING & DRILLING live show

The new outline of ARTTEC I table type CNC cutting machine had been published since 2015, and now received successfully feedback from market.
In 2016, the updated cutting & drilling table type machine had published in the market, and got good feedback!

Following is the live show of HochTech ARTTEC I cutting & drilling function.


And we are warmly welcome to check our machine's performance in our factory and in our exclusive distributor's place.

HochTech, cut what you want!

Plasma cutter, TopTech JCH100A live cutting for thick plate

TopTech JCH series air plasma cutter.
Cut what you want!
Satisfy requirement of hand plasma cutter, machine plasma cutter.
From 30A-50A hand held plasma cutter to 60A-160A machine plasma cutter, and higher for 200A-400A high power and high definition plasma cutter, cut what you want!

www.toptechone.com
info@toptechone.com
sally@toptechone.com

TopTech FAQ plasma cutting quality & main reason

TopTech FAQ

plasma cutting quality & main reason

I. The cutting surface is not vertical:

When we use the common plasma power source to cut, the best one will have a small angle of inclination about 3-5°. If the actual angle is bigger than 3-5°, that belongs to the vertical is not good, and the reason is as following:

A. Torch installation is not vertical to the plates: if cut a symmetric figure the angle is the same side, that is this problem.

B. Cutting direction is incorrect: the required side should be on the torch forward right side.

C. Torch height is not good: Negative cut angle (the bottom side is less) means the torch height is too low; Positive cut angle (the top side is less)

D. Torch spare parts need to change;

E. Cutting current is not good;

F. Cutting speed is not good.

II. The drows on the cutting part:

A. The spater on the top side: the spater on the both sides of the kerf

  Reason: torch is too low

  Solution: adjust higher arc voltage value to heighten the torch.

B. The drows on the bottom side:

--Cutting speed is too slow, and the shape of the drows are bolls and a lot.drows can be easy to move out.

Reason	Solution
Cutting current too large	Reduce cutting current and use the matched spare parts for the torch
Cutting speed too slow	Faster the cutting speed
Cutting height too low	Adjust higher arc voltage value to heighten the torch

--Cutting speed too fast:,the drows are fine rolls, and hard to move out.

Reason	Solution
Torch nozzle broken	Change nozzle
Cutting current too small	Increase cutting current and use the matched spare parts for the torch
Cutting speed too fast	Slower the cutting speed
Cutting height too high	Adjust lower arc voltage value to heighten the torch

Otherwise, the bottom drows also considered about air pressure and flow setting.

III. Didn't cut through:

A. The first piercing spot didn't cut through and lead the shape didn't cut through: the pierce delay time is too short, should be longer;

B. The first piercing spot had cutted through, but the following parts didn't cut through:

Reason	Solution
Torch nozzle broken	Change nozzle
Rusting, paint or other insulators on the cover of cutting materials	Move out the insulators
Cutting current too small	Increase cutting current and use the matched spare parts for the torch
Cutting speed too fast	Slower the cutting speed
Plates too thick for plasma power source	Change into suitable plasma power source

IV. The min hole cutting rules:

• Rules: The hole's inner diameter should be twice as the plate thickness;

• To cut small hole the inside will be a taper hole.

TopTech CNC cutting & drilling machine

TopTech CNC cutting, drilling, milling machine.

TopTech, cut what you want!

Say no more, just see the video.

www.toptechone.com

PROTEC live cutting work with Kjellberg + Eckelmann cutting controller

TopTech PROTEC gantry CNC cutting machine

It can equip with 8 flame torches at the same time, and 2 plasma torches at the same time.
Protec gantry CNC flame & plasma cutting machine is for high accuracy requires.
It equip with German Eckelmann cutting control systems, anti-collision torch holders.
Protec gantry CNC cutting machine machine body is designing for high definition plasma power sources, such as Hypertherm, Kjellberg, Victor, TopTech JCH plasma power sources.

CUT WHAT YOU WANT!
www.toptechone.com
sally@toptechone.com

TopTech Exclusive Secret Tips --How to improve CNC cutting effective? (I)

TopTech Exclusive Secret Tips--How to improve CNC cutting effective? (I)

The main difference among CNC cutting, manual cutting and shape cutting is the cutting speed, accuracy, which CNC cutting is the best than the other two. But there was an issue that some customers had purchased CNC cutting machines, and the working effective wasn’t improved. The mainly reason is that they don’t know much knowledge about CNC cutting machine and can’t use them with high proficiency. For this kind of situation, we’d like to share TopTech exclusive secret tips as following.

TopTech ARTTEC III HD plasma cutting machine

I.CNC controller is not stable will lead slow cutting.

The heating of CPU and hard ware in CNC control system leads the system unstable

and can’t run stable. The damage of fan, shaking of hardware or virus influence lead procession stop. And also it maybe the bug of CNC cutting system software, which shows error or cutting error. It also will delay cutting process and then influence on cutting quality issue.

II. No using nesting software leads cutting materials low-usage.

No using nesting software, and using manually nesting on CNC controller system for the parts to do the parts cutting, this is wasting of time and materials. So please using nesting software, which comes with TopTech CNC cutting machines together. And the more details of this point secrets tips will share on the second part of this article.

III. No Auto cutting technology and cutting parameters database in CNC system.

Operators adjust CNC cutting machines parameters only with eyes and experience,

which can’t make auto piercing and auto cutting. This makes cutting machines with low effective.

IV. Using unsuitable cutting way.

During cutting, the cutting way is too simple, e.g. cutting every parts need pierce every time and need cut the full parts. No co-edge, borrow edge, bridge connection, etc. high effective cutting ways, lead cutting low effective and cutting consumables (esp. plasma torches’ consumables) waste a lot!

Hope if customers noticed the above points, it can improve CNC cutting machines

more effectively and save more cutting materials.

TopTech after sales contact info:

Email: info@toptechone.com

Skype: info-toptechone

Plasma cutting machine--TopTech ARTTEC I

TopTech ARTTEC I plasma CNC cutting machine.
Table CNC cutting machine.

Table type CNC cutting machine, cutting thickness range is from 0.3mm-25mm.

Working with any type air plasma power sources.



CUT WHAT YOU WANT!



www.TopTechone.com

sally@toptechone.com